Hubs are getting hard to find everywhere - in the US, Ebay is one
source. For the last year I've been collecting every hub I see (both 10
and 100) at junk stores, yards sales, even friends throwing them away
because they are "upgrading" to switches. Anyone who may even have to
troubleshoot a network should do the same. The has to be some old hubs
in your country somewhere....
For your immediate problem, could you install Wireshark on CPU
192.168.1.105 <http://192.168.1.105/>? If not, then I don't know of a
software-only solution to your problem.
Good luck,
-JB-
Hendra Gunawan wrote:
Thx for the information jb.
is there any software can capture the data especially. In my country
there isn't any 10m hub anymore. sorry i'm novice about this.
thx b4.
regards,
hendra.
On Jan 4, 2008 9:27 AM, jbartas <jbartas@xxxxxxxxxxxxxxxx
<mailto:jbartas@xxxxxxxxxxxxxxxx>> wrote:
Hi,
Your problem is the switch - it's designed not to send all packets
to all ports. A few years back I went looking for a way to force the
switch to do this. I had the same Linksys (maybe an older one), the
famous wrt54g. I never found a way.
Your simplest solution is to go to Ebay, buy a cheap old hub (NOT a
SWITCH!) and attach both your PCs and the wrt54g to the hub. Make
sure
you get 1 10Mb hub, not a 100 - IIRC the Linksys will only do 10. The
hub will forward every packet out every port, and you'll catch
them all
with Wireshark.
Someday I'll write up my proof that Ethernet switches not only
make
troubleshooting hard, they also slow down SOHO networks when
compared to
hubs. But that's another story.
Hope this helps,
-JB-
Hendra Gunawan wrote:
> Dear friend,
>
> I'm having problem, how to receive all traffic information from
> another cpu in my lan?
> because i want try to see all traffic from another cpu.
>
> my hardware configuration is ;
> i'm using router linksys wrt54g with 4 port swicth.
> my cpu using lan connection (ie 192.168.1.101
<http://192.168.1.101/> <http://192.168.1.101/>)
> and another cpu using lan too (ie 192.168.1.105
<http://192.168.1.105/>
> <http://192.168.1.105/>) and my router ip is 192.168.1.1
<http://192.168.1.1/>
> <http://192.168.1.1/>
>
> i want to see all traffiic ingoing and outgoing from
192.168.1.105 <http://192.168.1.105/>
> <http://192.168.1.105/ <http://192.168.1.105/>> but all traffic
can't be captured.
> i'm using wireshark Version 0.99.6a (SVN Rev 22276) and winPcap
4.0.1
> my cpu have been installed with etherdetect 1.3 with demo
version too.
>
> somebady can help me about this?
>
>
------------------------------------------------------------------------
>
> _______________________________________________
> Wireshark-users mailing list
> Wireshark-users@xxxxxxxxxxxxx <mailto:Wireshark-users@xxxxxxxxxxxxx>
> http://www.wireshark.org/mailman/listinfo/wireshark-users
>
--
John Bartas - Director of Network Engineering
Packet Island, Inc. www.packetisland.com
<http://www.packetisland.com/>
jbartas@xxxxxxxxxxxxxxxx <mailto:jbartas@xxxxxxxxxxxxxxxx>
cell: 408-857-0605
_______________________________________________
Wireshark-users mailing list
Wireshark-users@xxxxxxxxxxxxx <mailto:Wireshark-users@xxxxxxxxxxxxx>
http://www.wireshark.org/mailman/listinfo/wireshark-users
<http://www.wireshark.org/mailman/listinfo/wireshark-users>
------------------------------------------------------------------------
_______________________________________________
Wireshark-users mailing list
Wireshark-users@xxxxxxxxxxxxx
http://www.wireshark.org/mailman/listinfo/wireshark-users
--
John Bartas - Director of Network Engineering
Packet Island, Inc. www.packetisland.com
jbartas@xxxxxxxxxxxxxxxx
cell: 408-857-0605
