The setup will look like: http://wiki.wireshark.org/CaptureSetup/Ethernet#head-5220d760898496c38e928ed3d65ffc8160f6f3a6
Regards, ULFL
> -----Ursprüngliche Nachricht-----
> Von: Community support list for Wireshark <wireshark-users@xxxxxxxxxxxxx>
> Gesendet: 31.08.06 16:05:54
> An: "Community support list for Wireshark" <wireshark-users@xxxxxxxxxxxxx>
> Betreff: Re: [Wireshark-users] Using with a switch
so if you were to setup wireshark on a machine, i would need two NIC's on the machine that has wireshark running and have each NIC connecting to a respective port on the 3com 5xxx switch.
>
> one port would be setup as the monitor port and one setup as the mirror-port --- how was your 3com setup look like ?
>
>
> Thanks,
>
>
> On 8/31/06, Petr Vácha <vacha@xxxxxxxxxxx> wrote:
> FYI,
> 3Com 4xxx line names this as Feature->Roving analysis.
> 3Com 5xxx line uses terms Monitor port for ports to which you connect your sniffer and Mirroring-port for ports that send data to monitor port.
>
> Petr
>
>
> > -----Original Message-----
> > From: wireshark-users-bounces@xxxxxxxxxxxxx
> > [mailto:
> wireshark-users-bounces@xxxxxxxxxxxxx] On Behalf Of
> > Craig Wicker
> > Sent: Wednesday, August 30, 2006 5:01 PM
> > To: Community support list for Wireshark
> > Subject: Re: [Wireshark-users] Using with a switch
>
> >
> > Different vendors label this action different things:
> > SPAN Port
> > Mirror Port
> > Monitor Port
> >
> > My Cisco 4510R statement goes like this; your syntax may vary; and all
> > commands listed below are given from the Executive mode:
>
> > monitor session 1 source interface G4/10
> > monitor session 1 destination interface G5/10
> >
> > [where source is the interface I wish to capture from;
> > where destination is the interface I have plugged into with WireShark]
>
> >
> > show monitor session 1 (all)
> > no monitor session 1
> >
> >
> >
> > Craig Wicker
> > Hooker Furniture Corp
> > Network Administrator
> >
> >
> > -----Original Message-----
>
> > From: wireshark-users-bounces@xxxxxxxxxxxxx
> > [mailto:wireshark-users-bounces@xxxxxxxxxxxxx
> ] On Behalf Of Nathan J.
> > Churchill
> > Sent: Tuesday, August 29, 2006 3:01 PM
> > To: wireshark-users@xxxxxxxxxxxxx
> > Subject: [Wireshark-users] Using with a switch
>
> >
> > Hello:
> >
> > Our network runs with a switch. Can Wireshark pick up all
> > the connected
> > stations? I'm only seeing my own machine's traffic now. Can that be
> > changed? If so, how?
>
> >
> > Thanks.
> >
> > Regards,
> > Nathan
> > _______________________________________________
> > Wireshark-users mailing list
> > Wireshark-users@xxxxxxxxxxxxx
>
> > http://www.wireshark.org/mailman/listinfo/wireshark-users
> > _______________________________________________
> > Wireshark-users mailing list
>
> > Wireshark-users@xxxxxxxxxxxxx
> > http://www.wireshark.org/mailman/listinfo/wireshark-users
>
> >
> _______________________________________________
> Wireshark-users mailing list
> Wireshark-users@xxxxxxxxxxxxx
> http://www.wireshark.org/mailman/listinfo/wireshark-users
>
>
>
> --
> HBooGz:\>
>
> -----------------------------------------------------------------
> _______________________________________________
> Wireshark-users mailing list
> Wireshark-users@xxxxxxxxxxxxx
> http://www.wireshark.org/mailman/listinfo/wireshark-users
>
_______________________________________________________________________
Viren-Scan für Ihren PC! Jetzt für jeden. Sofort, online und kostenlos.
Gleich testen! http://www.pc-sicherheit.web.de/freescan/?mc=022222
