Jon,
it looks, that it is not depended on the traffic ethereal sees.
I do only a broadcast analysis with filter
not ip host <my ip>
Ethereal 0.9.16 and 0.10.3 seee the same traffic.
Only Ethereal 0.10.3 crashes.
Do You still want a sample tracefile ?
> Can you provide a sample dump that reproduces the crash?
>
> Regards,
> Jon Oberheide
> jon@xxxxxxxxxxxxx
>
>
> On Thu, 2004-04-29 at 06:38, Falk Hayn wrote:
> > Dear ladies and Sirs,
> >
> > ethereal 0.9.16 works fine with HPX-UX 11.11 in my enviroment.
> >
> > ethereal 0.10.3 core dumps under HPX-UX 11.11 when it starts to decode
> > packets.
> >
> >
> > ethereal 0.10.3 error messages:
> > ==============================
> > ** ERROR **: file proto.c: line 1153 (proto_tree_add_ipv4):
> > assertion failed: (hfinfo->type == FT_IPv4)
> > aborting...
> > ethereal: 24021 Abort(coredump)
> >
> >
> > libraries versions
> > ==================
> > all libs are used with ethereal 0.9.16 and ethereal 0.10.3 without any
> > changes
> > GTK 1.2.10
> > TCPDUMP 0.8.3
> > ADNS 1.1
> > UCD SNMP 4.2.6
> > PCRE 4.5
> >
> >
> > gdb backtrace session
> > =====================
> > gdb /usr/local/bin/gethereal core
> > GNU gdb 6.1
> > .... ... ...
> > This GDB was configured as "hppa2.0w-hp-hpux11.11"...
> > Core was generated by `gethereal'.
> > Program terminated with signal 6, Aborted.
> >
> > warning: Couldn't read general-purpose registers from `.reg' section in
> core
> > file.
> >
> > warning: The shared libraries were not privately mapped; setting a
> > breakpoint in a shared library will not work until you rerun the
> program.
> >
> > Debugging dynamic executables loaded via the hpux8 dld.sl is not
> supported.
> >
> > warning: Couldn't read general-purpose registers from `.reg' section in
> core
> > file.
> >
> > #0 0x00000000 in ?? ()
> > (gdb) backtrace
> > #0 0x00000000 in ?? ()
> > (gdb) Quit
> > (gdb)
> >
> >
> > gcc version:
> > ==============
> > gcc -v
> > Reading specs from
> /usr/local/lib/gcc-lib/hppa2.0w-hp-hpux11.11/3.3.3/specs
> > Configured with: ../gcc-3.3.3/configure --with-gnu-as
> > --enable-languages=c,c++,objc
> > Thread model: single
> > gcc version 3.3.3
> >
> >
> > machine:
> > ========
> > J2240, 2 Processors, 512 MB RAM, 1 Gig Swap.
> >
> >
> >
> > Can pls. someone give me advices, how to proceed ?
> >
> >
> > Do not hesitate to contact me via falk.hayn@xxxxxx if You have further
> > questions.
> >
> > With kindly regards
> > Falk.
> >
>
--
"Sie haben neue Mails!" - Die GMX Toolbar informiert Sie beim Surfen!
Jetzt aktivieren unter http://www.gmx.net/info
